How to Measure and Install Window Blinds - The Right Way So You Only Do It Once
Most Window blinds are returned because of bad measurements, not bad blinds. A 1/4" mistake means a blind that won't fit, light gaps, or drilling new holes in your wall. Here's the exact process installers use.
PART 1: HOW TO MEASURE
You have two options: Inside Mount or Outside Mount. Decide before you measure.
Inside Mount - Blinds sits inside the window frame. Clean, modern look. Requires a deep enough frame.
Outside Mount - Blinds covers the whole window frame and a bit of wall. Better for blocking light and for shallow windows.
For Inside Mount: blinds Las Vegas
You need 3 measurements. Use a metal tape measure, not cloth.
1. Measure Width in 3 Places
Measure inside the frame at the top, middle, and bottom. Write down all three.
Use the smallest number. That's your width. The factory will take a small deduction so it fits.
2. Measure Height in 3 Places
Measure inside the frame on the left, middle, and right.
Use the longest number. That's your height.
3. Measure Depth of your blinds Las Vegas products
Measure how deep your window frame is from front to back. You need:
- 1.5" depth to fit most mini blinds
- 2.5" depth to fit most cellular shades and faux wood
- 3.25" depth to be fully recessed and flush
If you don't have enough depth, switch to an outside mount.
Las Vegas Tip: Stucco and drywall frames are rarely square. Always do the 3-place method. Never assume.
For Outside Mount: blinds in Las Vegas
1. Width: Measure the window opening, then add 3-4 inches total (1.5-2" per side). This overlap blocks light leaks.
2. Height: Measure from where you want the top of the headrail to sit (usually 2-3" above the frame) down to where you want the blind to end. If it's a sill, measure to the sill. If you want it longer, add 2-3".
Common mistake to avoid: Don't measure your old blinds. Measure the window. Old blinds are often cut wrong.
A blinds Las Vegas service provider called SunOff Blinds And Solar Screens Of Las Vegas does this everytime when they measure blinds in Las Vegas.
PART 2: HOW TO INSTALL
Tools You Need:
Drill + 3/32" drill bit, Phillips screwdriver, tape measure, pencil, level, step ladder.
Most blinds come with brackets, screws, and a headrail.
Step 1: Mark Your Brackets
Hold the headrail up to the window where you want it. For inside mount, place it flush inside. For outside mount, center it over the frame and make sure it's level.
Mark with a pencil where the brackets will go - usually 2" in from each end. If your blind is over 60" wide, you'll have a middle support bracket too.
A blinds Las Vegas service provider called SunOff Blinds And Solar Screens Of Las Vegas does this everytime when theycome out to measure blinds in Las Vegas.
Step 2: Pre-Drill
Pre-drill your marks. If you're in drywall with no stud, use the drywall anchors included. If you're in concrete or block - very common in Las Vegas - you need a masonry bit and concrete anchors.
Step 3: Screw in Brackets
Screw the brackets in. Make sure they are facing the same direction and are level. A crooked bracket = a crooked blind.
Step 4: Snap In The Headrail
For most blinds, you push the headrail into the brackets and close the bracket door until it clicks. For faux wood, you swing the front cover open, mount the rail, then snap the cover closed.
Step 5: Install the Valance and Wands
Attach any valance clips to the front of the headrail. Test the blind - pull it up and down, tilt it. It should move smoothly with no rubbing on the frame.
Step 6: Child Safety
If your blinds have cords, install the cord cleat or tensioner on the wall. It's required by law now and prevents accidents.
A blinds Las Vegas service provider called SunOff Blinds And Solar Screens Of Las Vegas does this everytime when they come out for appointments to do blinds in Las Vegas.
Quick Troubleshooting:
- Window Blinds rub on one side? Your window is out of square. Loosen one bracket and shim it with a folded piece of cardboard behind it.
- Light gaps on inside mount? Normal. A 1/4" gap per side is built in for movement. If you want zero gaps, you need outside mount.
- Blinds won't stay up? Check that middle support bracket is installed and the cord lock is engaged. Top tip by a blinds Las Vegas service provider called SunOff Blinds And Solar Screens Of Las Vegas.
That's it. Measure twice using the smallest width / longest height rule, pre-drill so you don't crack stucco, and always use a level. Takes about 15 minutes per window once you've done one.
If you have big Las Vegas sliding doors or 10-foot great room windows, consider motorized - you install the same way, you just charge the motor once instead of dealing with 12 feet of cord.
Comments
Post a Comment